In this example, the rear end is pointed to the right of the centerline of the car. This w
Here we see where the rear end is aligned so that it is pointed to the left of the centerl
When taking measurements, you can use solid links in place of the shocks to locate the rea
Use a very fine line to mark each intersection. Find a marker with two ends, one fine to m
Use a good quality plumb bob to project points from the chassis to the floor. Use a piece
Here we see the layout for the process. Note that the lines formed by the intersecting mar
Having a good, well-balanced setup is a product of making sure all of the chassis elements are in place. Many times I have run across a car that has all of the right ingredients, such as roll-center design, a good balance of front and rear suspension design, proper weight distribution, and all the rest except one: a rear end that is not properly aligned.
Rear alignment is critical to the success of your setup. It can be the final setup parameter that can take you to the front or keep you in the rear of the field. The problem is that no amount of manipulating the other setup components will overcome a rear alignment problem. While it is probably true that a car out of alignment is more forgiving on dirt, it is important for both dirt and asphalt race cars to have a properly aligned rear end.
If youve ever followed an old pickup truck that has jumped one too many ditches and bent the rear suspension out of whack, youll know what an improperly aligned rear end looks like. Remember how it tracks sideways down the road, somewhat like a crab? That is exactly what is happening with your race car if your rear alignment is wrong, and it doesnt take much to really affect your cars performance. The rear axle centerline should be exactly perpendicular to the centerline of the chassis. Also, the right-side tire contact patches should track in line with each other, regardless of the difference in track width of the front and rear tires.
Tuning with Rear Alignment
Many racers have tuned the tight or loose condition of their cars by moving the right-rear tire forward or back. There are much better ways to adjust handling than this method. Using a small amount of rear steer as a product of chassis roll is a way to develop more bite, or free up a severely tight car (mostly on dirt tracks) and that is fine. But if a car tracks crooked down the straightaway and into the corner, the negative effect will be felt all the way around the corner.
How to Measure the Rear End
To measure your rear alignment, follow these simple instructions: Using the diagram, follow the numbered steps to set up a line that is 90 degrees to the centerline of the car and lays behind the rear end far enough to allow easy measurement. The car can either be at ride height or up on blocks placed under the tires with all the weight on them. It is much easier to have the car at ride height plus a constant amount in order to be able to crawl under the chassis to take measurements and make marks on the floor.
Position the Car
The best way to position the car is to put the car on jackstands or equivalent stable supports so the chassis is far enough off the floor for you to easily get underneath it. Add the ride height plus some constant distance to each corner. Remove the shocks and springs and place solid links where the shocks normally mount, so the rear end is supported in the same relative position that it would be at ride height with the tires on and all weight on them. We want to simulate the position of the rear end at normal ride height just like we will race the car.
If your car is a perimeter chassis (both sides of the frame are symmetrical), first measure between the inside framerails at the front and rear and divide those numbers by two. Measure from one side of the frame at the front and rear using the half measurements and place a mark on the floor at each end of the car at centerline. (I use a piece of 2- or 3-inch-wide masking tape placed on the floor to mark on.) These marks now represent the centerline of the car.
If you are measuring a straight rail (offset) chassis, measure the same distance (say 10 inches) off the front end of the straight rail and the rear end just in front of the rear axle and place marks on the floor to create a line that is parallel to the centerline of the car.
You will then have two points at each end of the car to use to develop a line that is at a right angle to the centerline of the car. Snap a chalk line or stretch a string over each of the centerline marks at each end of the car, forming a line. Make the line long enough to extend past the rear of the car. If you use a string, you can hold the string in place with spare lead weights or concrete blocks. That way, you can stretch the string tight and the weights will hold it firm.
Make a cross mark on the centerline somewhere behind the rear of the car.
Measure up the line toward the front of the car 96 inches (8 feet) and make another mark on the line. Again, you can use masking tape to mark on. I always cut 1 foot from the end of the tape so I can make an accurate measurement using the 1-foot mark and the 9-foot mark.
From the line you made in Step 2b, measure two distances, 10 feet from the front point and 6 feet from the rear point, to form an intersection on each side of the car. These two points will be used to construct a line that is exactly at a right angle to the centerline of the car.
Stretch a string or pop a chalk line over these two outer intersection points. The line that crosses the centerline should be directly over the rear 8-foot point on the centerline. If it is not, recheck all of your measurements and re-establish the intersecting points that form the perpendicular line.
The triangles formed on the ground (if you havent recognized it yet) are 3-4-5 right triangles whose sides have been doubled. In geometry, coincidentally, if a triangle has sides that measure 3 units, 4 units, and 5 units on each side, it is a right triangle. We just doubled the numbers, and we still have a right triangle. This is the easiest way to layout a perpendicular line.
Drop a plumb line down off the rear of each of the axle caps on each side of the rear end and mark a point on the floor. Be sure to use the same position on each side of the rear hubs. The hubs themselves are machined and are best to use. Dont use the back of the axle tube, especially if it is the original cast type.
These measurements should be the same. Adjust the length of the trailing arms to square the rear end.
Lateral Rear End Location
As well as making sure the rear end is perpendicular to the centerline of the car, we also want to make sure that it is positioned correctly between the rear framerails.
One of the handling adjustment methods that have been passed down through the years involves moving the rear end to one side or the other to change the handling balance. This is another unreliable and temporary fix that should not be necessary if all of the other chassis components are set up properly.
Alignment of the Right-Side Tire Contact Patches
I always recommend that the rear wheels be positioned so that the two right-side tire contact patches line up. This is because in the turns most of the weight is on the right-side tires and the car will want to track inline with the right-side tires where they contact the ground. Regardless of what you believe, it is important to know how the right-rear tire tracks in relation to the right-front tire.
Measure from the centerline you have created to the center of the right-front and left-rear tires. Make sure the front tire/wheel assembly is positioned so that it is correct in relationship to the cars chassis as it would be at ride height, like we did with the rear end. Adjust the length of the panhard/J-bar to align the right-rear tire to your particular liking.
This whole process should take about an hour or so. That is very little effort to make sure your car will track correctly and misalignment will not interfere with your cars performance. Repeat this entire process often, especially after kissing the wall or being involved in a crash. Once you are convinced that your car is aligned, you can then concentrate on the other important aspects of your chassis setup.